5 out of 5
Customer Reviews
By
xavier valdez
Date: March 31, 2022
It's way more convenient to use than the clip on build plate. I little tricky to align it properly when you're putting it back on but still preferable to dealing with those freaking binder clips.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
Michael
Date: March 29, 2022
Easy to use, tastes great.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Porkchop
Date: March 25, 2022
Be careful when putting in magnet strip only get one shot
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Robert Fischer
Date: March 23, 2022
Product as described. Thanks.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
ppresto
Date: March 23, 2022
Coming from the stock plate and a scrapper this is heaven on a build plate. Remove build from plate warm with your fingers, seriously impressed. Wiping down between builds with iso alcohol no marks at all. So far very happy with bed temps up to 70c max. Pla comes off with ease, it's true. Glad to have in my build plates collection. Ender 3S1 printer.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Shawn
Date: March 22, 2022
This works very well on the glass bed of my Ender 3 Pro.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Mike
Date: March 19, 2022
The enclosure is much larger than it needs to be for the stock Ender 3 Pro. It gives plenty of extra room for the additional filament guide and other add-ons that I have used to customize the printer.Rugged fabric. Make sure you push the tubes fully into the corner brackets.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Cody Tidwell
Date: March 17, 2022
Didn't think this would be worth it at first but low and behold. It's my new favorite bed. This with magigoo to add even more adhesion and then removing the magnetic plate from the bed after the print is done definitely helps removal.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
K
Date: March 15, 2022
Same magnetic mat that came with ender 3 pro
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Kev
Date: March 14, 2022
Update 3/15/2022: PLA sticks well, but PetG wouldn't let go! I'll have to experiment with lower bed temps to see if I can use it with PetG. Still love this surface! PLA goes down and doesn't move until you pop it off when the print is done.Original Review:I've been frustrated for a long time trying to get prints to stick to an after market CCTREE Ultrabase platform for the Ender 3 pro heated bed. I replaced it with this Creality Original Ultra Removable Magnetic 3D Printer Build Surface and now PLA sticks like glue.All those circles in the attached picture stick like glue thanks to this magnetic build surface!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
David M
Date: March 11, 2022
Bought this for the price, and you get what you pay for. No magnetic adhesion on the first one nor the replacement sent. One star because there no zero stars. useless. Go with the original just a couple of bucks more and avoid the time wasted repacking and returning this piece of rubbish.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Anthony
Date: March 10, 2022
Magnets are off 90 degrees. It would only hard lock 90 degrees the wrong way.I cut off the tab and it works just looks silly.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
danny chandler
Date: March 08, 2022
Don't waste your money on anything else. The magnet strength on this is way stronger than most generics. It's also roughly the same price. You do still have to use clips but the difference in quality between this and the other generics is uncanny.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Eric Morris
Date: March 07, 2022
When I took the first part off of it. It stretched out and now it won't lay flat at all. Not to mention the magnet barely holds. I used the original for 2 years this one lasted one print.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Bob B.
Date: March 07, 2022
I printed a lid for a clock weight and COULD NOT REMOVE the print .... at all .. tried reheating the bed, thru it in deep freeze .. no go. Heated bed to 110 .. no go. Ruined the part and had to pitch the print surface. Will try one more, if I have the same problem I'll us another brand and/or switch to glass. The original lasted a good 4 months with lots of use .. last one I ordered .. maybe 2 months. This one 1 print ..
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: March 02, 2022
When installing there was an adhesive magnetic sticker side to put on the build plate that was put on with no problem and no bubbles or any defects, but after setting the actual magnetic plate on and warming up the plate and leveling nothing printed as they should of if just printing on the default one on printer I ended up finding bubbles forming under the adhesive side as if heating and cooling was causing the expansion and contacting of the material off setting the plate leveling
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
charlie
Date: March 01, 2022
The printer I have came with this same removable print surface. The problem is it sticks to the base with magnetic adhesion, only the magnetic poles are not the same. The replacement pad doesn't stick well with the magnetic base on the printer unless you turn it 90deg and then the handle part of the pad makes it too wide. It comes with a new base so you can replace the one you have but it would be a lot nicer if the magnetic poles were the same.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Jakt
Date: February 26, 2022
Troubleshooting all the bad reviews: User Error!It is two sheets. Remove glass, peel apart top mat and bottom. Remove yellow wax paper and stick that sucker on after you figure out the direction the magnets are printed.Magnetic sheets are printed in horizontal lines. If it doesn't stick, turn it 90 degrees and try again. It bonds solid!Printing on glass was hit and miss for me. PLA sticks to it as if they are made for each other. Remove the top mat, flex and enjoy the crackle of your print coming off the surface.A must have along with your glass for other mediums.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Public Name
Date: February 23, 2022
Good adhesion and easy to get print off.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]