5 out of 5
Customer Reviews
By
Phoenix
Date: November 02, 2022
Once this is installed, it works great!Adhesion is great (though, I recommend using painters tape for PLA and some other filaments)Unfortunately, this installs like a cheap screen protector for a phoneYou have to stick a layer onto the metal bed, which will most likely get an air bubble underneath it when you do, and once its on its basically impossible to remove UNLESS you are willing to destroy it
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
Trey S.
Date: October 21, 2022
Couldn't remove skirt after my first print. Made of trash magnetic tape pretty much. Trash. Trash. Trash. I never write reviews EVER, but in hopes this stops even one person from wasting their time I decided to write it. DO NOT BUY.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Levi Smith
Date: October 07, 2022
I wanted to get away from the clips so liked the magnetic idea. That is definitely easier. But I originally went with the PEI plates as everyone seemed to say they were better. But for the life of me with 3 different PEI plates, textured, smoothed, etc. I can not get PLA to stick. I got maybe 3 things ever to stick and dozens of failures. I tried Z higher, lower, washing with dish soap, alcohol, roughing them up... No change. So got this original build surface and it's great. PLA just works every time(so far).
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Morgan Rae
Date: October 05, 2022
It works great! Now I did not get it for that exact 3D printer so I had to cut it down to fit mine. It works great though. Was super easy to stick it down. The top comes off with the print so easy. I am very happy I purchased this. Made it a lot easier for me. Just make sure if you're using it on a different 3D printer you raise the print job just a little so that it doesn't scrape this.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Lucas French
Date: October 04, 2022
Well worth the money. A way better set up than stock. Don't even need my puffy knife anymore. It also allows me to do multiple prints without having to retune the table
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Bruce B.
Date: October 03, 2022
While not an exact duplicate of what I had on my Ender 3's original matte, this is a good replacement and has worked very very well.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: September 30, 2022
Why is the bottom of this sticky, I thought it was magnetic
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Raydeeoh
Date: September 27, 2022
Works well, extra build plate for my Ender 3Pro.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jason H.
Date: September 26, 2022
if you have a printer, and dont have one of these, stop reading and buy one. If you have one and are looking for reassurance, let me tell you that I had two other removable surfaces before this one and this has by far given me the best results. magnet is strong and holds very well. If kept clean, it adheres easily and no problems were encountered. I got about 100 large prints on one so far, and it keeps being awesome.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Daphne Walker
Date: September 24, 2022
Perfect for any printer
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Bruce A.
Date: September 20, 2022
This bed is by far my favorite way to print pla. It's simple to remove and put back on. Pla comes right off as the mat bends, but sticks great when printing. Petg is a little harder to get to stick to it but can be done.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Thomas Fynes Jr
Date: September 19, 2022
This print bed isnt just for the ender series, if you happen to have a bed of the same size it will work! That's what I did for my Fokoos Odin and its amazing! Just be warned some printers may require you to move the end stop for it to work! Other than that this was a breeze to install. Simply remove the cover on the back of the magnet and stick it to the metal part of the build plate. Then put your new build plat on it and BOOM you're good to go! Great build plate!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Serafin Velez
Date: September 06, 2022
A
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: September 06, 2022
You might need to buy some 3d printer glue sticks to help the adhesion, otherwise super easy to remove prints, and super easy to clean just use hot hot water
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jaybers
Date: September 01, 2022
This is by far my favorite 3D printing bed. It simply pulls off with magnets, and prints are super easy to remove. Installing wasn’t too hard either. But the bed isn’t exactly the same dimensions as the Ender 3 bed, slightly bigger on the edges. It doesn’t change anything, but you just need to be careful when leveling it for the first time. Overall super great product! Would buy again.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Ronald
Date: August 24, 2022
I’ve used it once. I don’t need it or see the point. My bed does just fine
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Hugo
Date: July 25, 2022
For the price it's unbelievable! Super flexible magnetic mat that peels the print right off. No scraping or fear of breaking thin bits. I was in disbelief by the price and ease of installation and use.... First time I thought it was a gimmick or a trick....I can never go back to the stiff plate that came with my machine.... It's a dedicated PETG plate now that I don't care what happens to. I've printed PLA and PETG only but haven't had any strange behavior from the plate out of either. Highly recommend!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Fernando
Date: July 24, 2022
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
michael weispfening
Date: July 24, 2022
This is great. Easy to install and the magnet really holds it in place. I have seen people say that it melts at higher temps around 90-100 degrees on the bed. Why do you need it that hot?? 60-70 is perfect (depending on the filament of course). And use alcohol to clean.Recommended. Edit: also make sure you place the adhesive right on the table. Because once you get a bubble you might as well start over and get a new one.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Michael Fitzgerald
Date: July 22, 2022
It's in the title. This is very convenient and way better than the original plate. I even like it more than my glass plate
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]