5 out of 5
Customer Reviews
By
Bruce A.
Date: September 20, 2022
This bed is by far my favorite way to print pla. It's simple to remove and put back on. Pla comes right off as the mat bends, but sticks great when printing. Petg is a little harder to get to stick to it but can be done.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
Thomas Fynes Jr
Date: September 19, 2022
This print bed isnt just for the ender series, if you happen to have a bed of the same size it will work! That's what I did for my Fokoos Odin and its amazing! Just be warned some printers may require you to move the end stop for it to work! Other than that this was a breeze to install. Simply remove the cover on the back of the magnet and stick it to the metal part of the build plate. Then put your new build plat on it and BOOM you're good to go! Great build plate!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: September 06, 2022
You might need to buy some 3d printer glue sticks to help the adhesion, otherwise super easy to remove prints, and super easy to clean just use hot hot water
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Serafin Velez
Date: September 06, 2022
A
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jaybers
Date: September 01, 2022
This is by far my favorite 3D printing bed. It simply pulls off with magnets, and prints are super easy to remove. Installing wasn’t too hard either. But the bed isn’t exactly the same dimensions as the Ender 3 bed, slightly bigger on the edges. It doesn’t change anything, but you just need to be careful when leveling it for the first time. Overall super great product! Would buy again.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
christopher
Date: August 25, 2022
Supposed to be magnetic. The build plate moves with the slightest touch. Have to use clamps to print.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
Ronald
Date: August 24, 2022
I’ve used it once. I don’t need it or see the point. My bed does just fine
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Tyler Zdanowicz
Date: August 24, 2022
I only print with PLA and this has worked absolutely amazing. I leveled the bed initially after getting it... I haven't had to level the bed since! This works way better than my stock bed
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
SammyB
Date: August 18, 2022
The magnetic material in the mat does not adhere to the Ender 3 pro bed unless it is turned sideways! So if you wanted a spare mat and your original is good, you can’t switch between the two. Not happy.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Y. J.
Date: August 14, 2022
After 8 months and around 15 prints the top started to pel off with the prints. So, I must buy a new one.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
kyle z
Date: August 13, 2022
sticks to the print almost to well easy to pop on and off though
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Hlywine
Date: August 12, 2022
This mat works great for adhesion, but like many have already mentioned, the magnet part is offset by 90. Which means if you install it the way it's supposed to go on, it doesn't stick very well to the table. I tried printing like that but in the middle of my print it shifted and messed up my print.So I just turned it sideways to test and yes, it sticks on like a glue. So all I did was cut off the tab that sticks out with a razor blade and put it on sideways. Works like a charm now.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Adam Myszka
Date: August 09, 2022
I am impressed by this product in the worst way. The parts you expect to be sturdy, are flimsy and the nonstick surface has such high adhesion I almost ripped the build plate removing the first print. Additionally the magnetic hold is a fraction of what the default build plate provides. There is no way that this is OEM as the logo implies.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Hugo
Date: July 25, 2022
For the price it's unbelievable! Super flexible magnetic mat that peels the print right off. No scraping or fear of breaking thin bits. I was in disbelief by the price and ease of installation and use.... First time I thought it was a gimmick or a trick....I can never go back to the stiff plate that came with my machine.... It's a dedicated PETG plate now that I don't care what happens to. I've printed PLA and PETG only but haven't had any strange behavior from the plate out of either. Highly recommend!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
michael weispfening
Date: July 24, 2022
This is great. Easy to install and the magnet really holds it in place. I have seen people say that it melts at higher temps around 90-100 degrees on the bed. Why do you need it that hot?? 60-70 is perfect (depending on the filament of course). And use alcohol to clean.Recommended. Edit: also make sure you place the adhesive right on the table. Because once you get a bubble you might as well start over and get a new one.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Fernando
Date: July 24, 2022
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Justus
Date: July 23, 2022
Bed adhesion is not good, a little glue and good to go.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Michael Fitzgerald
Date: July 22, 2022
It's in the title. This is very convenient and way better than the original plate. I even like it more than my glass plate
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Michael Fitzgerald
Date: July 22, 2022
It's in the title. This is very convenient and way better than the original plate. I even like it more than my glass plate
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Doing it myself
Date: July 21, 2022
Have to say these because I'm on my third in less than 6 months. And that is my fault because, well, I suck at bed leveling my stock ender 3 pro. When my ender does work, I get days and days worth of prints without adhesion issues, I meaan, you do have to clean it when you get your oily hands all over it. The work as advertised. I will say however Ive not used exotic filaments. PLA, PLA and PETG so far.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]