5 out of 5
Customer Reviews
By
brohyde
Date: March 17, 2023
Worked perfect to remove a broken spark plug that a spiral extractor would not budge.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
Nikki
Date: February 27, 2023
A lot of the bad reviews might be from people using this incorrectly. Use a punch to give yourself a center, Make sure you're drilling COUNTERCLOCKWISE. And use a tap handle to extract by hand (again, counterclockwise).
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
Barbara Batt
Date: February 22, 2023
This was a gift for my son, and he was very happy with the quality.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
MRP52
Date: February 21, 2023
I purchased this extractor set to remove two badly rusted screws from a grill so that I could replace the burners. The bits were sharp and very hard tool steel. The only problem is that they don't come with a T-handle. After drilling each hole, I lightly hammered the extractor bit into the hole, and then gripped it with pliers. It worked, but a T-handle would have made the job a lot easier, as there isn't much to grip on the small extractor bits. Good quality bits though, and I would definitely recommend.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Chris
Date: February 03, 2023
Lifesaver. I snapped off a spark plug in my Chevy k1500. Apparently my torque wrench lowest settings was 20lbs and I only needed 10.I tapped the broken plug with 5 and a hammer, then used 1/2” 12 point socket 3/8 drive , on a 1/2 wrench with a 3/8 reduced for the added length. Use some penetrating oil like Pb blaster and once it gets going you should be able to twist out with your hand life saver
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Takeo_San
Date: January 20, 2023
Makes removing broken pipe nipples easy-peasy.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Trevor Crain
Date: January 02, 2023
Had some small metric hex screws that had stripped out. This extraction set worked flawlessly! Even on Stainless Steel screws.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Sherry St Pierre
Date: December 29, 2022
My husband is always stripping screws and snapping drill bits. He said these are very sturdy so I am glad I got them for his Christmas stocking.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Kalun
Date: December 22, 2022
works but drill bits are not as sharp as they should be
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Hastings
Date: December 18, 2022
Irwin has made a quality product here and it will work as it should as long as it's used properly and you take your time to do the job right.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
David
Date: November 05, 2022
Well first off it's Irwin and I have come to find Irwin tools to be of good quality. It's a very complete set and they arrived very fast
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
James Gash
Date: October 30, 2022
It did what it was supposed to but on my second bolt I needed to extract, the bit broke in half and had to use the next smallest bit to finish the job. Good value for the money if you have the time and know how to get it done and only need one bolt extracted.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Walter J.
Date: October 06, 2022
Bought these after reading craftsman's easy outs break. So I spent the extra money and got this set from Irwin. I had a stripped out head on an Allen head bolt, so I soaked it for a week in PB blaster, heated it with a propane torch drilled into it with the supplied reverse drill bit, hammered in the easy out and with pretty heavy torque the bolt finally broke free. This may be a small victory to some but it just paid for itself in my opinion. These drill bits and easy outs are tough as nails and didn't break under heavy pressure. I would definitely recommend.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Philip Rakowski
Date: October 02, 2022
Very well built bits and extractors. Great value.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Poohbear
Date: October 01, 2022
I purchased this product a few years ago. I have attempted to use them multiple times. I like the fact that they have a drill bit with each extractor. However, the drill bits will not drill through butter. I have never drill out one screw or bolt with these. They are worthless. As for the extractors, they are not much better. They look good in the box, but are almost worthless based on my experience. Don't waste your money and purchase something else.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jacob E. Sammer
Date: October 01, 2022
Used several times now and worked like a charm everytime. Durability seems really good too.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Adam
Date: September 08, 2022
Works like a charm every time.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
cesar navarro
Date: September 08, 2022
Works as designed
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Brandon
Date: August 08, 2022
These have worked excellent for me as an extractor for soft metal and plastics. As most other bits do, they struggle against hardened steel. If you have to extract a broken bleeder screw in a cooling system, they will pay for themselves the first time you use them.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Amber L Neiser
Date: July 14, 2022
This kit was a little more expensive than others but I wanted something that worked. I had a broken exhaust manifold bolt stuck in the engine block. I started with the smallest bit and moved up to the next. Five minutes of work and the broken bolt was out. Combined with a T-handle tap wrench which made it a breeze to lock in and remove.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]