5 out of 5
Customer Reviews
By
Clarice S.
Date: February 22, 2021
I have a Costco task chair with mesh seat and back that I've loved. However, spending more time in the chair with covid the last year, I was yearning for a headrest. I didn't want to upgrade the whole chair, so looked for options. This was a risk, but worked out great. I drilled a couple 1/4 holes in the frame, and used some hardware I had handy around the house. I think riv-nuts or nut-serts would work well in this application as well. I've been very happy with the results.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: February 21, 2021
Pretty comfortable. Bit high, but that's just because of the high back chair, not the headrest.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Sal
Date: February 20, 2021
I really like this headrest, it is very affordable and sturdy. I attached it to my Office Star proline ii progrid manager's chair. Since the chair did not have holes, I used a 1/4 drill to make the holes and bought 1/4 28 nuts to tighten the screws (screws are provided). After attaching, it is very sturdy and comfortable! Thanks for all the great tips in the reviews.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Marina
Date: February 12, 2021
Very a good addition for a small price ...
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Catherine Harrison
Date: February 11, 2021
Easily attached to Leap V2 by drilling two 7/32 (or you could use 1/4inch drill bit) inch holes into the seatback and mounting with 1/4 hex nuts and fender washers as reviewer Dileep instructed. Very sturdy and looks good without using clamps.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
D-X
Date: February 08, 2021
Although not proprietary, I installed it on a Modway EEI-757 Articulated Office Chair, and it works perfectly. The only thing I had to do was to calculate the center vertical of the chair back rest and drill two wholes. The chair comes with the required screws, so it was very easy to install. It works great and hand can be easily adjusted to your liking. Great buy!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: February 06, 2021
As a product it's fine, but it would've been nice to have the mounting holes be adjustable to fit a variety of chairs so that I didn't have to drill holes into my chair to make this product work.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Peter Willis
Date: February 05, 2021
FYI I bought this because I thought it might fit my Leap v1, it doesn't, the v1 has a big lip on the back of the chair so the headrest base doesn't even come near the back. Will need to add some kind of long spacer or something. However it does look like it should be comfortable, and the head will tilt up/down as well as raise/lower. Only thing it's missing is being able to adjust horizontally
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Joseph Dixon
Date: January 28, 2021
Would've been a decent head rest if it had a vertical locking mechanism. Any slight head adjustment will push this thing down.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Cheryl
Date: January 18, 2021
Love this. Wonderful alternative to the expensive one that goes with my chair.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Cameron McCartney
Date: January 18, 2021
Drilled 2 pilot holes and installed this with no problems on my Work Pro Quantum 9000. I did have to sand the bottom piece of the support bar on chair to make sure headrest sat flush with chair. Would recommend if you are handy.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Alan Wong
Date: January 14, 2021
The mesh headrest fit with my Bayside Metro office chair by drilling into the plastic frame with washers and some screws I had laying around. One feature I would have liked is a locking mechanism that stopped the head rest from adjusting by itself whenever I would lean too back on it with my head and it would move back down with a jolt. The mesh is also a bit too flexible too my liking. Maybe the non-mesh version would be more firm.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Brett
Date: January 13, 2021
I also bought the C clamps the other reviewer recommended. Used angled connection on C clamp to compensate for lumbar pillow, worked perfectly (headrest was too far back in straight position as lumbar pillow causes you to sit further forward). Looks great, works great - it would be nice if headrest height actually locked as it will retract if you put too much pressure on it.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
modernoffgrid
Date: January 06, 2021
Took like 30min to drill the holes in my offbrand chair. Make sure to twist sr8 and level. You get one try only. The headrest is damb sturdy actually. Works as described
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Robert Sawtelle
Date: January 03, 2021
Works great
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Ycarol
Date: December 15, 2020
Worked out very well if you buy the attachment brackets recommended by other reviewers. I also need to buy two correct screws from Home Depot to secure the attachment brackets to the chair's back.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: December 12, 2020
Looks good, adjustable and similar color scheme to the classic aeron. I don't recommend the clamp method. Do the one with the furniture screws, hex nuts, and hooks. All together cost me around 28 dollars for a pretty solid headrest.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: December 11, 2020
Not much more than meets the eye, but that's fine since it's so cheap. Must have, and it makes it much easier to know that I'm not slouching. Works perfectly fine and install was a breeze.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Gastn Acosta Ramas
Date: November 24, 2020
I added this with two clamps to my Herman Miller mirra 2 chair, and it worked amazingly.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: November 20, 2020
Bought for a different branded chair, with the intentions of retrofitting it with this headrest and it turned out great! This headrest saved me from having to get a new chair just for a headrest.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]