5 out of 5
Customer Reviews
By
Romy
Date: January 31, 2021
I used this to clean up buggered up trailer spindle threads that someone had smashed up in the past. Worked great; a lot easier than replacing the spindle and much cheaper than a new axle.I haven't used it a bunch, just a few times cleaning up threads, but it seems decent quality. Fits a 46mm or 1-13/16 socket.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
Alex
Date: January 29, 2021
Purchased to straighten wheel stud threads on a metric 14 bolt axle
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
echo
Date: January 28, 2021
I didn't break it so it must be pretty good
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Mark E. Holbrook
Date: January 25, 2021
Cheap steel hogged out with dull cutting tools.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
patrick schantzen
Date: December 05, 2020
saved me money not having to buy a new axle
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Yan-frdric
Date: December 01, 2020
Very good product far price
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Russell Lewis
Date: November 23, 2020
Purchased the 5/8-24 good quality. To thread the barrel on my .308 works perfect the nut size is 1 1/4 would buy again for sure if i needed one of a different size
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
ParanaSlim
Date: November 23, 2020
This is the sheerest and thickest die I have ever purchased 5 stars in my book???
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jdandhogs
Date: November 17, 2020
Most of my die set you can tell what side to start with. This one I could not tell. But worked perfectly. A bit pricey but no one else had this odd size
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
me
Date: November 14, 2020
I bought this for 1 very specific reason. I needed a way to clean the melted 3d printer filament from my nozzle threads as I swapped them out. This is absolutely perfect for the job! Most 3d printer hotend nozzles are m6 threads and it having wrench flats makes it easy to put in a vise. For the $ this is the best option for what I needed it to do.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jimmyjud
Date: November 13, 2020
As advertised, 8mm x 1mm pitch. Sharp, durable, cut threads easily. Small, would not fit in my tap wrench but a crescent wrench worked fine. Delivered by due date.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
Domengo
Date: October 31, 2020
Ordered M24x1.5 hex die to freshen/salvage the thread on a CV joint hub. It works as intended. $34 for one, Chinese-made tool, which will probably sit in my workshop drawer for another 10 years, unused. Take it or leave it, I was unable to find anything locally, and replacing the hub would easily cost close to $100.It does seem pretty robust, though. What I like is that it's thick enough to turn it with a large wrench onto. I didn't have any box wrenches or adjustables big enough to accomodate it, so I wound up using a monkey wrench. Not my best moment, but the job got done, and my BMW is back together.The hex dies that have the recessed area and matching bad reviews seem to be for smaller diameter threads.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Hud H.
Date: October 28, 2020
Solid product that solved my issue!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
old schooler
Date: October 24, 2020
Rethread some bolts
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
nevin bretz
Date: October 19, 2020
I used it to clean up some damaged threads on my 2012 Ram 2500's rear wheel studs. It cleaned all 16 easily with plenty of more life left.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Shozi Sami
Date: October 16, 2020
Excellent little die. It is very small and a bit hard to handle but such is the nature of a tiny tool. Very affordable.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
richard c.
Date: October 04, 2020
easy product to use
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: September 21, 2020
Works for me. However I was only chasing out damaged threads as opposed to cutting new threads.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
JH
Date: September 04, 2020
Worked great
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Joesph C.
Date: September 03, 2020
Cut too much percentage of thread off bolts
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]