5 out of 5
Customer Reviews
By
Robert O. Cox
Date: September 26, 2021
Worked smooth with a bit of olive oil for lube.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
Heod Mosa
Date: August 30, 2021
lo he usado varias veces para hacer nuevas roscas en un material duro y si a resistido, lo volvera a comprar
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: August 27, 2021
This showed up in short order and worked perfectly
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Don
Date: July 01, 2021
Used primarily on bronze and cast iron. Held up well. Well built
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Mark Stephenson
Date: June 28, 2021
Worked great as promised
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Mnl4jc
Date: June 07, 2021
It worked perfectly with my Hogue Freedom Fighter installation kit.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Robert J. Shunkwiler
Date: March 04, 2021
Works great.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Brennen
Date: December 26, 2020
This broke 10x faster than an Autozone tap, which says a lot. It only has 2 flutes and the cross sectional width at the tip is about 1/8”.It broke instantly. I've never quite seen anything quite like it. I got less than a quarter turn into cutting, maybe 5ft/lbs of torque and it snapped. I don't know how you could tap anything made of steel with this. The company is called “Drill America” but its certainly not made in the U.S. Luckily, it was so brittle that I was easily able to punch the fragments out of the hole with a proper piece of tool steel. Buyer beware.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Ian L
Date: December 14, 2020
this is much more durable than other options.Smooth tapping...0 complaints.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Gene
Date: December 09, 2020
They work well in mild steel.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
Jeff Dickinson
Date: December 02, 2020
Works great
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
sandra sander
Date: November 20, 2020
Good price and they came on time
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Sam Davis
Date: November 15, 2020
Used this to tap the lower receiver to allow a 4-40 set screw to capture the pivot pin detent spring. Worked perfectly. This is a “Must do” improvement in my opinion and for less than $10, there's no reason not to. Use the JT Custom 4-40 x 1/8” set screw kit and you're set
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
SkeeterUSA
Date: October 18, 2020
I had one bolt hole in my table saw cast iron top (Powermatic 66) that was damaged. I'm a woodworker, not a metalworker so I was concerned about making a bad problem worse. This tap has a tapered end that allows it to hunt for the existing good bolt threads. It did just that and I was able to repair the damaged opening threads in a matter of minutes. I couldn't be more pleased.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A nerd
Date: October 01, 2020
I needed to find a way to keep my volvo's door on. The plastic mounting brackets that the door screwed into wore away (car is nearly 20 years old) so i needed a solution to keep my door attached. I used epoxy putty, let it harden, then tapped it with this. Works great, had to pre-drill a pilot hole for this to get into the epoxy. Threads worked perfect for my - 20 threaded hex screws.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Austin Wright
Date: August 14, 2020
Complete garbage. Sheered off after the third tap of mild aluminum extrusion. Would not recommend.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
charlie j.
Date: August 03, 2020
I have used it a lot,Its well made
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Dr Ice
Date: July 29, 2020
If you need to chase the threads on an AR-15 receiver pistol grip because some knucklehead cross threaded it, or because the receiver left the factory without fully cut threads, this is the one you need. 1/4-28. Cuts 7075-T6 aluminum like butter.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]