5 out of 5
Customer Reviews
Items 1 - 14 of 14 reviews
1
By
Sheila Nybo
Date: January 10, 2018
Does the job.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
Red
Date: September 28, 2017
Used for a Rifle build, a one-time use tool. But I needed it. It is well made and feels very heavy duty.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Jeannette
Date: September 09, 2017
Tool was needed for a special job
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Michael McGarghan
Date: September 07, 2017
Not a lot to say, it arrived as describbed, chrome plating was decent, I only had to use it a couple times for a torque wrench requirement on a barrel nut. Doubtful that I will use it in enough or other opportunities to give it tests of it's durability, but it was adequate for job and good deal for the $.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
William Nall
Date: July 23, 2017
Quality wrench with one drawback, the thickness is just oversize for the application I had in mind. Unfortunately I'm installing AR-15 barrel nuts and the max width of the wrench flats it .5in this crowsfoot is a .6 bummer but for the price I'll have it around for other work.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Carl129
Date: July 15, 2017
Fit the barrel nut on my LR308 build perfectly, at only 40 to 60 FT-LBS it's fine, not sure that I would trusted for serious industrial/mechanical work.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Tommy M.
Date: June 20, 2017
It's a little thick for the barrel nut I needed it for but it worked.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
A Customer
Date: April 22, 2017
Just a bit too thick for what I need. But I will make it work.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
CalRal
Date: March 13, 2017
Like most of the reviewers here, I purchased this to torque a barrel onto a rifle. It did the job just fine. The clearances were tight enough to work with the JP barrel nut wrench. The finish quality is exactly what one would expect for a ten-ish dollar tool. Maybe not everyday use quality, but I would recommend it to anyone that might use it in a similar application for a few things.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
letchgolf
Date: February 08, 2017
worked good for the one job I needed it for.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Deans
Date: February 05, 2017
1-3/1634; crow foot: Good tool but as others have mentioned, beware of the tool's thickness. At 5/834; thick it may not fit applications where the tool thickness needs to be minimal.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
WOPR
Date: February 05, 2017
Worked well for my application. Tolerance seemed pretty tight.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Anphonic
Date: January 25, 2017
This is exactly what I need for ONE fitting, with one small drawback. The wrench itself if to thick which means I'll have to make it thinner before I can use it for my needs. It's a very tight space between a boss fitting and hydraulic motor and I would expect it to have been thinner as scenarios like this are exactly what it was intended for.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
mruseless
Date: November 30, 2016
Reasonable for the price. Had to grind it down a bit since it was 1/834; too thick for the barrel nut I bought it for. But satisfied overall.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
Items 1 - 14 of 14 reviews
1