High quality and easy to install.

Worked perfectly for what I needed.

This plug extension isperfect...

Installed easily, painters tape and running hole saw in reverse on fiberglass is the trick. Gasket deformed a bit as it tightened down, but hopefully that means a good seal. I used a small amount of silicone as well for insurance.

I needed a male power plug for a busy workbench/chest of drawers, and the tight angled offset in this plug's wiring was just the ticket. I bought the less expensive 'Dumble Power Inlet Port' first and tried to modify it to fit. Bad move. After cutting it up I couldn't send it back, and the cutting merely made a messt. The NOCO plug cost almost twice as much, but the angled wire clears the drawers and the cabinet perfectly, so the cost of the Dumble plug goes in the tuition column. (NOCO makes a number of fine products BTW. I have had 100 success with them.)

I installed this in my 2022 Sierra Denali 3500 to use as a transition the my onboard battery tender. See the batteries in the truck go dead after 5 days so I had to install aa two battery tender. It works perfectly.

Fits my dog very well. I bought this harness to replace the same unit but a smaller size when my puppy was smaller. Easy to put on and take off.

Very well-built, great value for your money

Installed this along with the NOCO Genius 2D battery charger / maintainer on my 2004 Jeep Wrangler TJ Rubicon. Installed the port on the passenger side front fender well and the Genius 2D right below the air box on the passenger side inside fender. The only issue I had was I had drilled the 2 hole and did not account for how deep the port sits in the hole. My solution for this was getting a hockey puck and cutting it in half and using it as a sort of spacer between the port and the fender well. It worked perfect and is the exact same diameter as the port itself so unless you look closely you can not even tell I used it. This was to prevent the back of the port from hitting the A/C lines right behind where I drilled the hole. The port does include some self tapping screws but I opted to replace those with bolts and nylon locking nuts just to be a little safer and make sure it never comes loose. Another thing I did was purchase 1 heat shrink tubing and putting that over the plugs from the Genius 2D and the port itself just to insure it does not come loose or get water, dirt, etc. inside the connectors there. I absolutely love this and it makes for a faster, easier, and more convenient way of plugging my Genius 2D in, instead of having to open the hood and find the cord that way or dangle it down below the engine. The product feels super high quality as well. Very happy with my purchase.

Used for a month plugged into twice thats the ground is super loose

I would like to say that this came packaged perfectly and securely i am verypleasedand happy with it

Very high quality and same day delivery, you can't beat that.

I took a star off because while it has 3 holes, it only came with 2 self tapping mounting screws, which... I mean, come on, there's not a lot to QC before this thing goes out the door, can't you at least make sure it's got the right number of screws?

Makes life a little easier when it come to recharging batteries on a boat. No longer have to climb in the boat, unlock the compartment, find the plug, charge the batteries and reverse the procedure. Just pull a cord to the boat and plug it up. Very easy to install the plug. Just find the spot you want to install it, drill a 2 hole, install the plug and attach with screws which are self tapping. Advise drill pilot holes for the screws much easier to screw them in on an aluminum boat.

Well built, looks and works great. Only nit I have is that I replaced the steel mounting screws that came tin the unit with stainless (mounted on my boat used in salt water). Recommended!

Just what I wanted and easy to install. It came with everything I needed except the 2 drill bit...... Now I dont need to take my cover off to charge the batteries

Purchased and mounted on my bulldozer battery box compartment to which the onboard battery charger/maintainer is plugged into on the other side. Works flawlessly from a good heavy extension cord from wall receptacle to bulldozer power inlet. Nothing to roll up and put away on the dozer itself.

Instructions say to drill a 2 hole, which I did but due to the way the cord attaches on the back side still didnt work. Had to put a pretty big notch in the interior paneling to clear the cord. Would have been 5 stars if not for that issue. Just what I was looking for and works great other than installation issue.

I used it as my power source input into an ATEM Mini Pro inside of a waterproof case. Perfect!

The fit was perfect