Easy to use and very good quality. Best adhesive for repairs.

Anybody who has used this product knows it great and this ida great value

Anybody who has used this product knows it great and this ida great value

J B products always work. Used for many years. Follow instructions, work clean and allow to cure.

Works great

I didn’t have high hopes for this but caught it on sale and wow it actually worked! My bed leg broke so just mixed the paste and next day no movement glued on good.

The leg broke off my grandmother's heavy cast iron outdoor table, the table was from the early 1960's and I inherited it. I mixed up a small batch of this epoxy and clamped the leg for 24 hours. I can't believe it's as good as new, but I will have to repaint the table due to the gray color of the epoxy which oozed out.

Used it on the handle of a heavy porcelain coffee filter which gets used with boiling water every day and it's been solid for months.

Used to repair cracks on thick PLASTIC 8-D battery case cover. After initial coat I added some fiberglass cloth and covered with additional epoxy. Product is very dark gray color.

Used the product to place golf club head back into shaft. Has worked perfectly.

I have worked both professionally and personally my entire life in engineering or build and repair. JB weld products are a go to for everything, as long as you choose the correct product for your repair and use it correctly. In this case- we are talking about the steel reinforced full cure time JB weld. (People often jump onto the quik version, but there are drawbacks to that). I n two recent cases I used this on hard plastic surfaces (it does well on metal when done correctly). You must mix it evenly and correctly. your surfaces must be clean. do a dry run fitting with whatever clamping and holding device you are going to use. the JB must be applied evenly and excess removed, and possibly redistributed. If the surfaces match without gaps, do not over apply -otherwise the bond will be weaker, not stronger (the less is more principle here- just a little extra past the thin layer' is ideal). clamp or secure the joint and leave it alone for 24 hours. Seriously that last part. I think people try to test it or play with it too soon. Don't touch it. The items that I repaired recently, really I did not expect even this to work. (the first being on a fitbit 4, the small clip where the body clips to the band is notorious for breaking. This area takes a lot of pulling force and it has held up for weeks on my wrist and getting taken on and off and the band being pulled and so forth- the second is an area on a set of expensive headphones that has a weak spot that again - this holds without issue). There are no other products that compete with the correct JB Weld product. As long as the use matches the product (I have used the high heat, I have used the underwater, I have used the steel stick, and the plastic specific) and that the instructions are followed. I have used this on metal as well, and as a filler, with good results. I know with thousands of reviews mine may seem insignificant, but i want to add to the list on the good side.

Car bumper

Tenia una tubo del agua con una fisura y con el epoxy lo repare excelente producto100 recomendado

I'll just say, be careful what you glue with this, because getting it off will be impossible. Everything around this epoxy will break first. This is the best stuff. It's one of those things that is so good at what it does, you worry about scarcity should you ever need it, and it isn't there.

It was the best 50 years ago when I first used it and it still is. Doesn't degrade over time either like many other epoxies.

Fixes everything, easy to work with, paintable, never breaks. Awesome stuff.

So I’ve had a set of high-end Italian-made stainless steel cookware for 30 years. Absolutely the best cookware I’ve ever had. However, a couple of months ago the metal handle on one pot lid snapped off at the spot weld connections. I was not going to throw the lid away!I’m not into welding so I decided to try heat-resistant adhesive. First, I tried regular epoxy. I wA careful yo clean all grease and water mineral residue off the lid and hackle first. Epoxy Didn’t hold - the handle popped off on first use.So next I tried high-strength heat resistant super glue. I was careful to clean off all residue from the epoxy, and glued the handle back on. Once again, the handle popped off the lid on first use.So I tried this as a third time, and it seems to be the charm. The adhesive is easy to mix, but does take about four hours to set up. I used some tape to hold the lid handle in position while the epoxy set up. After that, I waited another day for the epoxy to gain full strength. It has worked so far. My wife has been using the lid again for about one month, and you’d never know the lid had been repaired.Highly recommend this epoxy for applications needing high store and heat resistance.

Have not yet tested the weld under heat, but so far everything appears about right.

Used this to mend the reclining release on a reclining chair.

I like how easy it was to mix and spread on the object you need to fix, I used it to fix my gaming chair and a bike and both are still functioning.